Issue#1294: Radio Control - Quanum V2 second screen

  • Hi,
    Probably been answered a million times but I can't find it.
    If the v2 has 2 video outputs....could 1 be plugged into a second screen for someone to view?
    My daughter loves to come watch a few of us fly and would be great if I could give her a bit of the FPV experience too

    Cheers

    0 Answers

    Sorry, your answer is too short !

  • Issue#470142: Radio Control - Video of my Quanum Nova issue Please Help

    Hello I have obvious issues with this new Quanum Nova. Every now and then I'll loose ailerons while in flight. The craft will hover and all other functions work as the should during these times. Video sums it up and it doesn't happen all the time. I have done the following remediations All calibrations per the sticky for cheerson/quanum Disassembled and checked for loose connections New battery Esc calibration Any help would be greatly appreciated! Quanum Nova quadcopter with aileron issues (0 min 38 sec)

  • Issue#901: Radio Control - Park zone Sport Cub aileron issue

    Park zone Sport Cub First flight ended with a crash, bent prop, ed nose cowl Replaced parts Getting airplane ready for my second flight with it and I noticed that the right aileron is a few degrees down with the stick centered. Any ideas? And yes, I'm new at this. And yes I've thoroughly checked out all the transmitter settings,servos,links,horns, clevises, etc.. Thanks guys for any advice

  • Issue#1923: Radio Control - SW capacitor/ librepilot issue HELP!!

    Hi all, I have a problem.. My Eachine landed from about a metre flat on its belly and the SW capacitor came off, and one off the connecting pins broke so I replaced with a 470uf 25v from maplin.. LibrePilot takes longer than usual to choose the FC in wizard then on setting the motor start points that SW motor runs seemingly slower and rattly, then on saving the wizard settings it gets to preparing mixer settings and crashes there. That's about as much info as I have as I'm new to this and only had my Eachine 2 days Thanks in advance

  • Issue#3839: Radio Control - SkyZone 5.8Ghz 200mw Range issue

    Hi! i am very new to Quad flying and am having a little trouble with my FPV Setup, i purchased the Quanum V2, http://www.hobbyking.com/hobbyking/s...Tx_Rx_Set.html, and the Quanum Nova quad, been having heeps of fun flying but when i tried to get the goggles to work i was getting less than 15m without the no signal warning, i have the Transmitter mounted inside the quad with the antenna poking out between the two front rotors, ( i can post a pick if you need) is there something interrupting the signal because of this mounting point? when i am next to the drone the signal is clear as day without much static at all, any ideas why this is happening? Thanks!!!

  • Issue#5755: Radio Control - HobbyKing X200 10A Touch Screen Charger - $40/Shipped!

    Hey guys, up for sale is a used HobbyKing X200 10A touch screen charger. This is the AC/DC version *however* the AC power supply has failed and the charger only works with a DC power supply now. But it still works fine, I use a 20v DC power supply w/o any issues. I have removed the AC power supply parts from the case and attempted to fix it, but was unsuccessful, and I will be including the AC parts for you in a separate bag if you want to try and fix it. There is a soldered in fuse that keeps blowing, I'll include my extra replacement fuses, I also tried replacing the bridge rectifier, that did not help. You can practice you electronics repair skills or toss it, up to you. Yes it works using a DC power supply! :) $40 gets it shipped to you asap!! Thanks! Attached Thumbnails Views: N/A Views: N/A Views: N/A

  • Issue#8246: Radio Control - Uncontrollable Yaw Issue

    I have an F330 clone frame that has an Openpilot CC3D FC, HK 25/30a ESC's and Propdrive 28-26s 1200kv motors. I hooked it up to the Openpilot GCS and went through the FC and transmitter configuration steps. The problem is that after arming and taking off, it wants to continually yaw left and kind of bounce up and down making it hard to control. I checked most settings and everything looks fine including the motor RPM speed sliders as well as I completed the ESC calibration and double checked that the props are on correctly. I also looked on my Turnigy 9xr controller settings and it looks like it is correct. I am not sure what to do next. This is not my first quad but I am clueless what to do next. Everything is new with the exception of the ESC's and motors. Thanks! John

  • Issue#10242: Radio Control - DJI iOSD Mini On-Screen Display for Real-Time Flight Information (Black)

    Brand new never been used before DJI iOSD Mini On-Screen Display for Real-Time Flight Information (Black) $58 shipped Attached Thumbnails Views: N/A Views: N/A

  • Issue#11626: Radio Control - Issue with TDisaster

    Just wanted to get the word out- I bought a battery from TDisaster. He was extremely responsive on the day I pm'ed him about buying the battery and was quick to take my money, but all but disappeared afterwards. Payment sent on 1-11-16. About a week after I sent payment, 1-17-16, I sent him a PM asking for the tracking info because I should have received the battery by then. A couple days went by then he said that he was too busy and didn't get it out but that he would do so shortly. That was a week and a half ago and I still have no battery and he hasn't replied to a PM in ~four days. It's now 1-26-16 and still no battery or response. Here is the original FS thread http://www.rcgroups.com/forums/showthread.php?t=2569355 I'll update if I hear anything or if there ends up being a positive resolution. Just wanted to get the word out since he has some other stuff for sale too. EDIT: And now his PM box is full.

  • Issue#11927: Radio Control - SkyRC Quattro B6AC issue

    This is the second SkyRC Quattro B6AC I have and both seem to have the same issue. One of the four charging circuits has given up the ghost. This one pictured the top right gave up and the second the bottom right. I emailed SkyRC and of course no response to 2 emails for customer service. I opened up the unit itself in hope it was four separate charging circuits boards and I could find a replacement or combine for one functioning charger. Question is anyone had this issue with this brand or Hitech they are identical in every way. If so were you able to trouble shoot the problem? Attached Thumbnails Views: N/A

  • Issue#12861: Radio Control - Walkera qr x3560 pro gps issue

    Hi Guys... Greetings from Barcelona.. i am new on this forum and i hope you can help me out with this issue. I've got a walkera qr x350 pro since few months already with over 30 hrs flight and never had an ssue till last week when my GPS started having some problems of connections. I followed all procedure as usual but after callibration, the gps light didn't start blinking as it used to do in the past so i could not fly on gps mode. I opened but everything seems ok inside...it might be the antenna or something else? I would need your advices whenever possible Many thanks in advance

  • Issue#13704: Radio Control - Quanum Trifecta - PNP - $150 shipped

    Selling my awesome little Quanum Trifecta Tri-Copter. It folds up into quite a small package... I've even it it in a large coat pocket. Built by an experienced modeler (me) and features the following components: SunnySky X2204 GemFan 5x3 Turnigy MG-9018 servo Naze 32 Will sell for $150 shipped in the lower 48. Actual shipping elsewhere. Attached Thumbnails Views: N/A Views: N/A Views: N/A

  • Issue#17569: Radio Control - Android HOTT Viewer App Issue

    Hi guys. Has anyone else experienced the issue of Rx and Tx Reciever signal data not being shown using the HOTT Viewer App on a Samsung Galaxy 3 ? Any ideas? Attachment 8646219 Attached Thumbnails Views: N/A

  • Issue#18991: Radio Control - Complete Quanum DIY FPV set

    Quanum Complete FPV Bundle Set w/ Goggles, 5.8GHz 32ch Video TX & RX, CP Antennas and Camera(PNF). This is brand new only used it once in my rock crawler. Comes with everything including the gopro camera pigtail so you can use a gopro camera if you want and three 3S lipo (2 elite and 1 thunder power) batteries. I did the viewing lense upgrade for a bigger viewing area and will include the original one also. Guaranteed to work! $110.00 shipped. I know hobbyking sells this for $99 but I'm including 3 Lipos and the upgraded lense. Thanks for you time. Lower 48 only please. Attached Thumbnails Views: N/A Views: N/A Views: N/A Views: N/A

  • Issue#26371: Radio Control - FTDI Adapter issue?

    Hi, I am having weird issue with my silabs ftdi adapter with windows 10. First, I have the driver installed. I have been reading around seeing that FTDI has installed an update in windows that bricks any (knock off) FTDI chips. Is this a result of it? Background, I had Windows 10 pro since it first released. I have flashed a minimosd or two within that time with this same FTDI adapter with no issues. I recently cleaned my desktop with a fresh install of Windows 10 pro. Anyone know what or why this is happened? Thank you. http://www.readytoflyquads.com/cp2102-usb-adapter (note I saw a few videos of Arduinos getting bricked as well. Could something have happened to where I bricked this?

  • Issue#28074: Radio Control - Quanum V2 goggles

    Quanum V2 goggles Skyzone 32 channel RC832 receiver I added some ATV goggles so they are more comfortable to wear and to seal off any light that shines in with the normal foam strips that they include with them. $80.00 shipped in US only! Attached Thumbnails Views: N/A Views: N/A Views: N/A

  • Issue#28097: Radio Control - Power issue

    Hello, New here and just trying to get into a multirotor hobby, so I purchased the LS 128 Sky Hunter. Flew it for a bit, crashed the heck out of it, but it is pretty durable...and now have a quick issue. When I full power it, it remains at about half power and it doesn't come off the ground, but...when I yawl it right at full power, it goes to full power...yawling left full power does nothing. So 2 of the motors are engaging full power (yawl right) and 2 are not. I have made no modifications to it. Sounds like there is a disconnect somewhere, but I am not sure where to begin. I took the unit entirely apart and all wires seem to be connected. Anybody have any ideas?? Thanks

  • Issue#30476: Radio Control - Quad drops out of the air, suspect Emax 1806 2300kv de-synch or motor issue?

    Hi All, I was hoping some quadcopter experts could help me diagnose a quadcopter issue. I have a ZMR250 quad (had about 1 month) with naze32 FC, 4x DYS BL20A ESC and 4x Emax 1806 2280KV motors. The issue i'm having is that the quad sometimes just drops out of the air! I can fly for a while then it just drops out of the sky, once it occurs it seems to re-occur more frequently. When it occurs the motor does not feel hot. I don't think its a power delivery issue, it flys ok for a while till the issue occuers, all motors connect to the same power distribution board and the connections are good, if it was a power issue I think other motors/ESCs would have the issue too. I'm using 1300mAH 45C battery which should be fine. This has been happening for a few weeks now or at least more frequently over the past few weeks. Trouble shooting I have tried: 1) Checked all connections 2) Initially I would stop the motors to prevent damage when it crashed. I searched for possible issue and I think it

  • Issue#32224: Radio Control - windows phone as FPV screen

    Hi guys.. Have an old Lumia 920 that I want to use as a screen in home made goggle for fpv. Someone here can help me out with an app to use the phone for this?

  • Issue#32226: Radio Control - Quanum Nova / Cheerson CX-20 tumbled from the sky

    Hello everybody. Well, as per the title, I am quite new at this but I believe I am not a complete newb. I bought the Nova from HK, got the PNF version, managed to get it working with my Turnigy 9X. Also installed a Q-2D. Today as I was flying it and bringing it towards me, it suddenly did 2 somersaults and planted itself in the ground. A few details about the flight. I took off from around 1200m above sea level, I took it up about 450m, brought it down a bit abrubtly, as shown in the video later, while gliding in circles to avoid my own turbulence. Also I am using Phantom 3 props. After it crashed, I had a bit of a climb to get to it, when I found it after about 3 minutes, the 2 motors that weren't planted in the ground were still spinning. I picked it up, removed the battery, and touched the motors. one of them was piping hot, and another one was very hot as well, not as hot as the first, but still quite a bit. The battery was cool, the ESC's I couldn't get to at that point to che

  • Issue#33094: Radio Control - DX 9 Issue

    I want people that own the DX 9 Transmitter to know of a problem I have found when trying to set gain values for your Aircraft. My example is what happens when trying to set gain values in Servo Setup. The setup is as follows. Flight Mode Setup Aux 2, 3 position switch for my Gyro Go to Servo Setup and stay in Travel. Go to AX2 and set your gain value to 15 for the top value and 20 for the lower value. Flip the switch and notice that even though it is calling out Mode 1, 2 and 3 both top and bottom values show as selected and will both change at the same time. You might have to go a little lower with the values for this to happen but non the less it will happen. Once this happens you will not be able to set flight mode 3 and both upper and lower values will be selected and will change without you knowing (assuming your looking at your plane while flying and setting the gain without looking) In short you might think you flipped your gyro off to land only to find out that the g

  • Issue#35645: Radio Control - fatshark teleporters v3 viewing issue

    I have a fatshark teleporter v3 rtf system,no matter how i place the googles on my face,theres always a blurred image .....heres why. It seem like the lenses are too close together,or my eyes are too far apart. If i shift googles left,left lens is clear,right is blurry and vise versa. Is there a way to resolve this? Has anyone sucessfully moved the lens,or lcd over slightly to correct this issue? If i mod it,move just the lenes over slightly.....would the focus be altered? Im only needing to move each lens about 1/8 further away from center. But i would hate to ruin a nice pair of googles.

  • Issue#35652: Radio Control - delta ray issue

    just got a delta ray,but it will only fly in safe mode,will not fly in intermediate or expert mode,when I switch to these modes it turns to the left and nosedives,panic button works but when released in these modes,crashes,any ideas? :confused:

  • Issue#39522: Radio Control - Tarot Retract issue

    Having issue with Tarot retracts on latest build. One leg only travels half way when wired up to LG controller. Plugged into either side produces same results. Figured it was the leg. But seems to work fine when powered directly and bypassing controller. If the problem is the control unit, why no issue with other leg? Is this fixable / tune-able? Adjusting endpoints / travel in TX does nothing. Or should I roll the dice an order new controller? Any input is appreciated. https://www.youtube.com/watch?v=BZ-4G7qIG84

  • Issue#48382: Radio Control - Quanum nova unlock motors

    Hi all. New to this quadcopter caper although familiar with fixed wing models etc. Purchased a quanum nova from HK and followed all of the very limited instructions but then found a very informative vid on HK. Followed the instructions to the letter but could not get the motors unlocked with the throttle stick right (mode 2). Tried my Taranis plus with DR8-ii and then with an hk orange receiver. Both times the rx bound fine and using Mission Planner controls all appeared to be working fine. Got frustrated with not being able to unlock motors and sent it back to HK. Got replacement and what do you think exactly the same - cannot unlock motors. I must be doing something wrong but have followed the HK video again and cannot work out what I am doing wrong. Does the compass have to be calibrated and connected. The only thing that is not 100% clear in the HK video is exactly which wire is connected to the Rx to power it up. There are three cables but only one of them has a signal, + and - th

  • Issue#48386: Radio Control - X8R Range Issue

    I am aware that this topic has been raised in several different forums but after hours of reading I still do not have a clear picture of how to resolve it in my particular case. I have X8Rs in several fixed wing aircraft bound to a Taranis 9X Plus transmitter running OpenTX in D16 mode, all of which meet range tests comfortably and fly with plenty of operating range. I also have an X8R in a small quad which I first flew bound to an XJT module in a Turnigy 9X running Er9x, again in D16 mode. It did not take long for me to realise that the quad had a serious range problem, with complete loss of normal signal at about 60-70 metres. I first thought that this was due antenna setup but more careful orientation yielded no improvement. At that point I started researching X8R range issues on the internet and found lots of questions but no clear answers. Most of the discussion was around the Taranis/X8R combination. Out of curiosity I switched transmitters over to the Taranis with no notic

  • Issue#53876: Radio Control - Quanum Falcon FPV 250 Racing Frame

    Used Quanum Falcon FPV Racing Frame forsale Normal wear, nicks and scratches, but no structural damage. This frame looks to be made by the same company as the QAV 250. Actually the same geometry, just a little different frame shape . Frame, under frame PDB and angled FPV camera mount. XT-60 pigtail , installed front and rear Diatone LED's . Nylon standoffs for FC. Velcro battery strap. I never got around to building it up. $25.00 shipped, paypal only, lower 48, PM with interest. Attached Thumbnails Views: N/A Views: N/A Views: N/A

  • Issue#55767: Radio Control - Dji Lightbridge and WooKong-M issue on Evo S800

    Hi, I am desperate for help with connecting the Lightbridge to the WooKong-M on the Evo S800 using Futaba radios, we originally used the AVL58 transmitters but have swapped it out for the DJI Lightbridge, we cannot find any information on how to connect everything together, we can connect to the HD GH4 Gimbal ok but when we connect the Lightbridge Bus cable to the X2 port on the WooKong-M, we have a major problem, the motors startup right away!!! Very dangerous, can you help us with a diagram or detailed description on how to connect the DJI Lightbridge with the WooKong-M flight controller please we need to be flying again as soon as possible. Do we need special settings on the Futaba 14SG radio? can you help us to solve the instant motor startup issue? Thanks in advance. First time posting!

  • Issue#56470: Radio Control - RMRC Dvr with screen or similar

    Looking for a Dvr with screen preference is RMRC but let me know what's you have. Asking Price shipped Thank you Attached Thumbnails Views: N/A

  • Issue#56486: Radio Control - member issue

    Member's tag line isn't all that nice: http://www.rcgroups.com/forums/member.php?u=240367 I'm fine with an anti-fan club, but profanity in the tag line is uncool for RCG. Apparently member just yesterday took offence to a "delete post" notice from a year or so ago when I scrubbed a pile of trolling posts out of this thread after it became sticky: http://www.rcgroups.com/forums/showthread.php?t=1348435 Subsequently he's sent me some less than cool PM's. would be cool if the PM's stopped, but I can ignore them. The tag line above needs to change though. Cheers, Arron